Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Mehr...
Federdruck hält vordere oder hintere Rampen / Sockel an Ort und Stelle - auch bei .45 Sights perfekt; Vielseitiges, vollständig anpassbares Design; Hervorragende Brennerbeseitigung
Behebt das Problem, dass die Rampe beim Schmelzen des Lotes verrutscht, mit einem spitzen, federbelasteten Kolben, der den Druck auf die Rampe oder ein Visier konstant hält, auch wenn das Lot fließt. Passt die Höhe, den Winkel und die Stärke des Federdrucks an. Der nicht beschädigende "V" -Block zentriert den Lauf unter dem Kolben. Hält auch die Kimmersockel fest. Tolle Fackelfreiheit.
TECHNISCHE DATEN: 5,1 cm lange Aluminiumbasis. Insgesamt 10,2 cm hoch. 3,5 cm (1-3 / 8 ") langer Oberarm. 5,1 cm (2") lange Kolbenstütze, 7,6 cm (3 ") lange Kolbenbaugruppe.
Mehr...
Kundenbewertungen zu BROWNELLS RAMP SOLDERING JIG
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 3,5
Love this Jig(21.05.2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31.07.2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.
Artikel-Nr.: 080739000 BROWNELLS RAMP SOLDERING JIG050806104372 Behebt das Problem, dass die Rampe beim Schmelzen des Lotes verrutscht, mit einem spitzen, federbelasteten Kolben, der den Druck auf die Rampe oder ein Visier konstant hält, auch wenn das Lot fließt. Passt die Höhe, den Winkel und die Stärke des Federdrucks an. Der nicht beschädigende "V" -Block zentriert den Lauf unter dem Kolben. Hält auch die Kimmersockel fest. Tolle Fackelfreiheit.
132.9EUR3132,90 €
*
Lieferzeit ca. 14-21 Werktage. 3 Stk. im Zentrallager USA
Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Mehr...
Federdruck hält vordere oder hintere Rampen / Sockel an Ort und Stelle - auch bei .45 Sights perfekt; Vielseitiges, vollständig anpassbares Design; Hervorragende Brennerbeseitigung
Behebt das Problem, dass die Rampe beim Schmelzen des Lotes verrutscht, mit einem spitzen, federbelasteten Kolben, der den Druck auf die Rampe oder ein Visier konstant hält, auch wenn das Lot fließt. Passt die Höhe, den Winkel und die Stärke des Federdrucks an. Der nicht beschädigende "V" -Block zentriert den Lauf unter dem Kolben. Hält auch die Kimmersockel fest. Tolle Fackelfreiheit.
TECHNISCHE DATEN: 5,1 cm lange Aluminiumbasis. Insgesamt 10,2 cm hoch. 3,5 cm (1-3 / 8 ") langer Oberarm. 5,1 cm (2") lange Kolbenstütze, 7,6 cm (3 ") lange Kolbenbaugruppe.
Mehr...
Kundenbewertungen zu BROWNELLS RAMP SOLDERING JIG
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 3,5
Love this Jig(21.05.2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31.07.2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.