Brownells Österreich - Einer der größten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schießsportzubehör Österreich

BROWNELLS
1911 AUTO HSS LO-MOUNT SIGHT BASE CUTTER

080621495
65\ Shoulder x .495"
These cutters are specially designed by us and made to our specifications for cutting the sight base slot required to mount the Wichita and Novak Lo-Mount 1911 Auto sights. Use ¼" carbide end mill to remove the bulk of the material (see drawing above) then make final dovetail cut. Final cut to lower rear of slide is done with an end mill and is not a part of the sight base cut. Made slightly undersized to compensate for variations in sight bases and milling tolerances on installation. With the popularity of custom 1911 Auto Pistols, this cutter is one that you will use frequently in your custom work. CAUTION: For use in milling machine only. 2" (5cm). .495" diameter cut. ½" (12.7mm) diameter shank. 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.
51.9 51.9 1 EUR
Artikel-Nr.: 080621495
BROWNELLS 65 HSS LO-MOUNT SIGHT BASE CUTTER .490" Diese Fräser wurden speziell von uns entwickelt und nach unseren Spezifikationen zum Schneiden des Visierbasisschlitzes hergestellt, der für die Montage der Wichita- und Novak Lo-Mount 1911 Auto-Visiere erforderlich ist. Verwenden Sie einen ¼-Zoll-Hartmetall-Schaftfräser, um den Großteil des Materials zu entfernen (siehe Zeichnung oben), und führen Sie dann den letzten Schwalbenschwanzschnitt durch. Der letzte Schnitt an der unteren Rückseite des Schlittens erfolgt mit einem Schaftfräser und ist nicht Teil des Visierbasisschnitts. Leicht gemacht Unterdimensioniert, um Variationen in den Visierbasen und Frästoleranzen bei der Installation auszugleichen. Mit der Popularität von Custom 1911 Auto Pistols ist dieser Fräser einer, den Sie häufig bei Ihren Custom-Arbeiten verwenden werden. ACHTUNG: Nur zur Verwendung in Fräsmaschinen. 2" (5 cm ). Schnitt mit 0,495" Durchmesser. Schaft mit ½" (12,7 mm) Durchmesser. 65° Schulter. 700 U/min NICHT ÜBERSCHREITEN, BEI HÖHEREN GESCHWINDIGKEITEN BRECHEN DIE ZÄHNE.
51.9 EUR 0 51,90 € *
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Eigenschaften: Degree: 65

Eigenschaften

Degree: 65 Versandgewicht: 0,045kg Versandhöhe: 5mm Versandbreite: 76mm Versandlänge: 140mm




65\ Shoulder x .495"
These cutters are specially designed by us and made to our specifications for cutting the sight base slot required to mount the Wichita and Novak Lo-Mount 1911 Auto sights. Use ¼" carbide end mill to remove the bulk of the material (see drawing above) then make final dovetail cut. Final cut to lower rear of slide is done with an end mill and is not a part of the sight base cut. Made slightly undersized to compensate for variations in sight bases and milling tolerances on installation. With the popularity of custom 1911 Auto Pistols, this cutter is one that you will use frequently in your custom work. CAUTION: For use in milling machine only. 2" (5cm). .495" diameter cut. ½" (12.7mm) diameter shank. 65° shoulder. DO NOT EXCEED 700 rpm, HIGHER SPEED WILL BREAK TEETH.
Newsletter