Eigenschaften
- Modell: Government,Officers,Commander
- Waffentyp: 1911
- Versandgewicht: 0,009kg
- Versandbreite: 57mm
- Versandlänge: 89mm
- UPC: 841370100842
Artikeldetails

Preise inkl. MwSt., zzgl. Versand
Artikel-Nr.: 296100001
Herst.-Nr.: 10362
841370100842 Der aus Stahl gefertigte Schlagbolzenstop ist breiter und dicker als der Standard, sodass du ihn für einen engen Sitz anpassen kannst, der hilft, die Extraktorspitze quadratisch zur Patronenrand zu halten, um die Auswurf- und Zuführungsleistung zu verbessern. Die untere Kante bleibt quadratisch, bereit für die endgültige Anpassung, um das Öffnen des Schlittens zu verlangsamen und die Verweildauer mit Munition mit hohem Energiegehalt zu erhöhen. Wärmebehandelt auf Rc 48, mit abgerundeten Ecken, die Rissbildung widerstehen, für eine lange Lebensdauer. Erhältlich in Kohlenstoffstahl mit einer robusten schwarzen Oxidbeschichtung und rostfreiem Stahl. Die Serie 70 ist speziell so dimensioniert, dass sie einen lückenlosen Sitz bei .45 ACP Colt Serie 70 Pistolen und Klonen bietet. Die Serie 80 passt auf 9mm/.38 Super/.40 S&W/.45 ACP Colt Serie 80 Pistolen und Klonen.
Kostenloser Versand ab 299,00 €.
Lieferzeit ca. 14-21 Werktage.
Der 1911 Oversized Firing Pin Stop von EGW ist die perfekte Wahl für alle, die ihre 1911 Pistole optimieren möchten. Dieser speziell gefertigte Stopp ist breiter und dicker als der Standard und ermöglicht es dir, ihn für einen perfekten Sitz anzupassen. So bleibt die Extraktorfläche quadratisch zur Patronenrand, was die Extraktion und Vereisung verbessert.
Kohlenstoffstahl (CS), schwarze Oxidoberfläche oder Edelstahl (SS), natürliche Oberfläche. .48” (12mm) breit, .65” (16.6mm) hoch, .133” (3.3mm) dick. Anpassung durch einen Büchsenmacher erforderlich.
Thank You EGW 06.08.2016
Finally, or I just may be late to the game, a firing pin stop that cures clocking. I have now installed this firing pin stop in four different brands of 1911s and have been very pleased with the results. Fitting times may vary, but the average is about 30 minutes, start to finish. This is not a drop-in part. Elbow grease is required. Also, for best results, just lightly burnish the leading edge instead of rounding it off like the factories do. If you want a radiused FPS, buy a drop-in. But, if you want a tight fit that also slows down the recoil impulse, get one of these.
Qaulity firing pin stop by EGW 08.03.2016
Nice part i would recommend this for someone wanting a tight fitting stop in stainless for an 80series 1911, there are not many options out there this is a good one though. I fit the stop by filing the sides until it could be pushed in by my finger with a snug fit, make sure that you chamfer the bottom of the stop were the hammer rubs.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.