Brownells Österreich - Einer der größten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schießsportzubehör Österreich

BROWNELLS
AR-15/M16 OFFSET RECOIL BUFFER RETAINER

430105818
Introducing the Brownells Offset Buffer Retainer - a solution designed to enhance the reliability and longevity of your AR-15's performance during the firing cycle. A common issue for AR-15 builds is a gap between the bolt carrier and recoil buffer. If you’ve ever seen “chatter” marks on a buffer, that is indication there is a gap when the firearm is assembled. This problematic gap between the carrier and buffer leads to the buffer retainer impacted the buffer on every firing cycle, making the chatter marks. This may also mean the bolt carrier is travelling without spring resistance for a short period, or is not getting the full force of the spring to go into battery or to prevent bolt bounce. This “offset” buffer retainer offsets the retention tab forward, allowing the recoil buffer to protrude further forward into the receiver, making full contact with the bolt carrier. Installation is simple, with it being installed much like a standard buffer retainer. The recoil buffer will orient the buffer retainer in the forward position. Machined from 4130 steel and finished with a black oxide finish, the offset buffer retainer will resist corrosion and hold up to intense firing cycles.
24.9 24.9 1 EUR
Artikel-Nr.: 430105818
BROWNELLS AR-15 OFFSET BUFFER RETAINER
Herstellerproduktnummer: OFFSETBUFFERRET Wir stellen Ihnen den Brownells Offset Buffer Retainer vor – eine Lösung, die entwickelt wurde, um die Zuverlässigkeit und Langlebigkeit der Leistung Ihres AR-15 während des Schusszyklus zu verbessern. Ein häufiges Problem bei AR-15-Konstruktionen ist eine Lücke zwischen dem Verschlussträger und dem Rückstoßpuffer. Wenn Sie jemals „Rattermarken“ an einem Puffer gesehen haben, ist das ein Hinweis darauf, dass beim Zusammenbau der Waffe eine Lücke vorhanden ist. Dieser problematische Spalt zwischen Träger und Puffer führt dazu, dass der Pufferhalter bei jedem Schusszyklus auf den Puffer prallte und Rattermarken verursachte. Dies kann auch bedeuten, dass sich der Verschlussträger für kurze Zeit ohne Federwiderstand bewegt oder nicht die volle Kraft der Feder erhält, um in die Batterie zu gelangen oder ein Zurückspringen des Verschlusses zu verhindern. Dieser „versetzte“ Pufferhalter versetzt die Haltelasche nach vorne, sodass der Rückstoßpuffer weiter nach vorne in das Gehäuse hineinragen kann und vollständigen Kontakt mit dem Verschlussträger herstellt. Die Installation ist einfach, da sie ähnlich wie ein Standard-Pufferhalter installiert wird. Der Rückstoßpuffer richtet den Pufferhalter in der vorderen Position aus. Der versetzte Pufferhalter ist aus 4130-Stahl gefertigt und mit einer schwarzen Oxidoberfläche versehen. Er ist korrosionsbeständig und hält intensiven Schusszyklen stand.
24.9 EUR 0 24,90 € *
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
Eigenschaften: Marke: AR-15 Menge: 1

Eigenschaften

Marke: AR-15 Versandgewicht: 0,045kg




Introducing the Brownells Offset Buffer Retainer - a solution designed to enhance the reliability and longevity of your AR-15's performance during the firing cycle. A common issue for AR-15 builds is a gap between the bolt carrier and recoil buffer. If you’ve ever seen “chatter” marks on a buffer, that is indication there is a gap when the firearm is assembled. This problematic gap between the carrier and buffer leads to the buffer retainer impacted the buffer on every firing cycle, making the chatter marks. This may also mean the bolt carrier is travelling without spring resistance for a short period, or is not getting the full force of the spring to go into battery or to prevent bolt bounce. This “offset” buffer retainer offsets the retention tab forward, allowing the recoil buffer to protrude further forward into the receiver, making full contact with the bolt carrier. Installation is simple, with it being installed much like a standard buffer retainer. The recoil buffer will orient the buffer retainer in the forward position. Machined from 4130 steel and finished with a black oxide finish, the offset buffer retainer will resist corrosion and hold up to intense firing cycles.
Newsletter