EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: CZ 75 CZ 75 SP-01 CZ 75 SP-01 Phantom CZ 75 SP-01 Shadow* CZ 85 CZ 97B CZ 97D CZ P-01 CZ P-07 (may require fitting due to a variance in dovetail dimensions) CZ P-09 (may require fitting due to a variance in dovetail dimensions) CZ PCR (there will be a gap under the front of the adapter plate) Tristar P120
Montiere dein Vortex Viper/Venom mit dem EGW Sichtmontage!
Die EGW Rotpunktvisiere sind so konzipiert, dass sie von links nach rechts montiert werden (mit dem Lauf nach vorne gerichtet). Die Schwalbenschwanzführung hat eine progressive Verjüngung, um die Installation zu erleichtern.
Einfach die hintere Visierung deines Gewehrs entfernen und durch die EGW Montage ersetzen, um dein Vortex Viper/Venom, Burris FastFire oder Docter Rotpunktvisier zu montieren. Du kannst die Montage jederzeit abnehmen und deine hintere Visierung wieder anbringen. Montagematerial ist im Lieferumfang enthalten.
Installationsanleitung
- Entferne die hintere Visierung*
- Installiere die EGW Sichtmontage in der Schwalbenschwanzführung
- Ziehe die Set-Schraube fest (falls zutreffend)
- Platziere das Rotpunktvisier auf der EGW Sichtmontage (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Sichtmontage erleichtert die Entfernung und hält Loctite vom Rotpunktvisier fern.)
- Trage blauen Loctite auf die mitgelieferten Montageschrauben auf
- Ziehe die Montageschrauben mit 15in/lbs an
2 Button Head Cap Screws - Bereitgestellt für Vortex Viper und Venom Sights
2 Flat Head Cap Screws - Bereitgestellt für Burris FastFire und Docter Sights
Die mit dieser Montage gelieferten Schrauben erfordern einen 5/64'' Inbusschlüssel für die Installation.
Eine Modifikation deiner Feuerwaffe kann die Herstellergarantie ungültig machen.
Dieses Produkt sollte von einem qualifizierten Büchsenmacher installiert und überprüft werden.
Es wird keine Haftung für Schäden oder Verletzungen übernommen, die aus einer unsachgemäßen Installation oder Verwendung dieses Produkts resultieren können.
Diese Montage passt auf:
- CZ 75
- CZ 75 SP-01
- CZ 75 SP-01 Phantom
- CZ 75 SP-01 Shadow*
- CZ 85
- CZ 97B
- CZ 97D
- CZ P-01
- CZ P-07 (kann Anpassungen erfordern aufgrund von Abweichungen in den Schwalbenschwanzabmessungen)
- CZ P-09 (kann Anpassungen erfordern aufgrund von Abweichungen in den Schwalbenschwanzabmessungen)
- CZ PCR (es wird eine Lücke unter der Vorderseite der Adapterplatte geben)
- Tristar P120