The Dead Level levels your reticle in relation to the Earth taking out any margin of error of the reticle not being perfectly level with the scope body. Simply attach your mounted scope to the Dead Level, level the device with the precision thumbscrews to center up the bulls-eye level, then just level the reticle with a predetermined level line or plumb bob. Aluminum Mil. Spec. Now features an Anodized Hard Coat Type III in a crimson and black finish. Instructions included. FOR USE WITH MIL STD 1913 PICATINNY COMPLIANT RINGS AND MOUNTS
Mehr...
Die tote Ebene gleicht Ihr Fadenkreuz in Bezug auf die Erde aus, um Fehler zu vermeiden, wenn das Fadenkreuz nicht perfekt mit dem Zielfernrohrkörper übereinstimmt. Befestigen Sie einfach Ihr montiertes Zielfernrohr am Dead Level, richten Sie das Gerät mit den Präzisions-Rändelschrauben aus, um die Bulls-Eye-Ebene zu zentrieren, und richten Sie dann das Fadenkreuz mit einer vorbestimmten waagerechten Linie oder einem Lot aus. Aluminium Mil. Spec. Jetzt mit einem eloxierten Hartputz Typ III in Hochrot und Schwarz. Anleitung liegt bei. ZUR VERWENDUNG MIT MIL STD 1913 PICATINNY COMPLIANCE RINGS AND MOUNTS
Mehr...
Kundenbewertungen zu BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 4,5
Excellent Tool(04.11.2013)
This tool is excellent at getting your scope perfectly level and tightening the scope in the rings. When shooting long range competitions it is important to dial in elevation from 200 to 1000 yards and not have windage drift. It is a bit expensive, but well worth it. Very solidly built. Will last a lifetime.
Good but not perfect(25.10.2014)
Pros:
Once I attached a set of rings to the rail, mounted the
scope a little loosely in the rings & levelled the base, it
was a quick job to level the reticle by looking through the
scope at a reference line from a self leveling laser level
line projected on the wall, rotating the scope until the
reticle matched the laser line, tightening down the rings
and rechecking the alignment.
Cons:
I found the integral bubble level hard to get centered so I
had to use another level to get the base level.
Because of the length of the rail, low rings don't work
well with it unless risers are added. A shorter rail would
Artikel-Nr.: 093000051 BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE Herstellerproduktnummer: 20050 Die tote Ebene gleicht Ihr Fadenkreuz in Bezug auf die Erde aus, um Fehler zu vermeiden, wenn das Fadenkreuz nicht perfekt mit dem Zielfernrohrkörper übereinstimmt. Befestigen Sie einfach Ihr montiertes Zielfernrohr am Dead Level, richten Sie das Gerät mit den Präzisions-Rändelschrauben aus, um die Bulls-Eye-Ebene zu zentrieren, und richten Sie dann das Fadenkreuz mit einer vorbestimmten waagerechten Linie oder einem Lot aus. Aluminium Mil. Spec. Jetzt mit einem eloxierten Hartputz Typ III in Hochrot und Schwarz. Anleitung liegt bei. ZUR VERWENDUNG MIT MIL STD 1913 PICATINNY COMPLIANCE RINGS AND MOUNTS
284.9EUR9284,90 €
*
Lieferzeit ca. 14-21 Werktage. 9 Stk. im Zentrallager USA
The Dead Level levels your reticle in relation to the Earth taking out any margin of error of the reticle not being perfectly level with the scope body. Simply attach your mounted scope to the Dead Level, level the device with the precision thumbscrews to center up the bulls-eye level, then just level the reticle with a predetermined level line or plumb bob. Aluminum Mil. Spec. Now features an Anodized Hard Coat Type III in a crimson and black finish. Instructions included. FOR USE WITH MIL STD 1913 PICATINNY COMPLIANT RINGS AND MOUNTS
Mehr...
Die tote Ebene gleicht Ihr Fadenkreuz in Bezug auf die Erde aus, um Fehler zu vermeiden, wenn das Fadenkreuz nicht perfekt mit dem Zielfernrohrkörper übereinstimmt. Befestigen Sie einfach Ihr montiertes Zielfernrohr am Dead Level, richten Sie das Gerät mit den Präzisions-Rändelschrauben aus, um die Bulls-Eye-Ebene zu zentrieren, und richten Sie dann das Fadenkreuz mit einer vorbestimmten waagerechten Linie oder einem Lot aus. Aluminium Mil. Spec. Jetzt mit einem eloxierten Hartputz Typ III in Hochrot und Schwarz. Anleitung liegt bei. ZUR VERWENDUNG MIT MIL STD 1913 PICATINNY COMPLIANCE RINGS AND MOUNTS
Mehr...
Kundenbewertungen zu BADGER ORDNANCE DEAD LEVEL SCOPE LEVELING DEVICE
Anzahl der Bewertungen: 2
Von brownells.com: 2
Durchschnittliche Bewertung: 4,5
Excellent Tool(04.11.2013)
This tool is excellent at getting your scope perfectly level and tightening the scope in the rings. When shooting long range competitions it is important to dial in elevation from 200 to 1000 yards and not have windage drift. It is a bit expensive, but well worth it. Very solidly built. Will last a lifetime.
Good but not perfect(25.10.2014)
Pros:
Once I attached a set of rings to the rail, mounted the
scope a little loosely in the rings & levelled the base, it
was a quick job to level the reticle by looking through the
scope at a reference line from a self leveling laser level
line projected on the wall, rotating the scope until the
reticle matched the laser line, tightening down the rings
and rechecking the alignment.
Cons:
I found the integral bubble level hard to get centered so I
had to use another level to get the base level.
Because of the length of the rail, low rings don't work
well with it unless risers are added. A shorter rail would