OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) is the latest member of the OPF line. G43x and 48 MOS slides are designed for direct mounting of the Shield RMSc sight. Trijicon's RMRcc is longer, and requires an adapter plate which also necessarily raises the mounting surface in order to mount an RMRcc. RMRcc has its own footprint. Gone are the two lug holes in front, these are replaced by two larger diameter threaded posts (bosses) through which the sight to mount/plate screws are installed. The sight to mount/plate screws are also significantly strengthened, though with the OPF-G, RMRcc design that holds the sight immobile on the plate, the larger diameter and stronger screws aren't as important, we always welcome screws that are less likely to strip. With the OPF-G43x/48, RMRcc, we didn't merely raise the mounting surface to provide a platform for the RMRcc. As RMRcc is longer than the G43X/48 MOS cut, the sight overhangs on the slide. When installed, the bottom of RMRcc (with Trijicon provided sealing plate installed) is almost flush with the top of the slide so the sight is as low as possible. We positioned the RMRcc towards the center of the plate as much as feasible, this is done to reduce the amount of unsupported overhang on the RMRcc's sealing plate in front. RMRcc has a rubber gasket around its battery compartment to keep water and moisture at bay, which pushes the sealing plate downward. This isn't an issue if the plate is of the same length as the RMRcc, but with an overhang, it creates a slight gap between the gasket and the sealing plate. OPF-G43x/48, RMRcc's design eliminates the gap/opening between the sight and sealer plate, to the point of emulating a plate that's as long as the sight itself. To wit, if the plate is as long as the RMRcc, it will make the installed height of RMRcc even taller, which is the very reason we chose to let the sight overhang. Torque value: Plate to slide: 12 to15 in·lbs. Sight to plate: 18 in·lbs.. Weight: 0.75oz Material: 1018 steel, black nitrided
Die perfekte Lösung für dein GLOCK 43/48!
Der TRIJICON RMRCC ADAPTER PLATE für GLOCK 43/48 ist die neueste Ergänzung der OPF-Serie von FORWARD CONTROLS DESIGN. Diese Platte ermöglicht die direkte Montage des RMRcc-Optiksystems auf deinen GLOCK 43x oder 48 MOS.
Produktbeschreibung
Die OPF-G43x/48, RMRcc (Optics Platform, Forward Controls, G43x/48, RMRcc) wurde speziell entwickelt, um die Vorteile der RMRcc-Optik zu nutzen. Hier sind einige wichtige Merkmale:
- Die G43x und 48 MOS-Schlitze sind für die direkte Montage des Shield RMSc-Visiers konzipiert.
- Da das RMRcc länger ist, benötigst du eine Adapterplatte, die die Montagefläche anhebt.
- Die Adapterplatte hat zwei größere, gewindete Posts (Bosses) anstelle der zwei Lughöhlen, die für die Befestigung des Visier-zu-Platte-Schrauben verwendet werden.
- Die Schrauben sind erheblich verstärkt, um eine zuverlässige Montage zu gewährleisten.
- Die RMRcc-Optik wird so positioniert, dass sie fast bündig mit der Oberseite des Schlittens abschließt, was die Höhe der Montage minimiert.
Wir haben die RMRcc so weit wie möglich in die Mitte der Platte positioniert, um den ungestützten Überhang der Dichtplatte zu reduzieren. Die RMRcc hat eine Gummidichtung um das Batteriefach, die Wasser und Feuchtigkeit abhält. Dies drückt die Dichtplatte nach unten, was bei einer Überhangmontage zu einer kleinen Lücke zwischen Dichtung und Dichtplatte führen kann.
Das Design der OPF-G43x/48, RMRcc beseitigt diese Lücke und emuliert eine Platte, die so lang ist wie das Visier selbst. Wenn die Platte so lang wie das RMRcc ist, wird die installierte Höhe des RMRcc noch größer, weshalb wir uns entschieden haben, den Überhang zuzulassen.
Technische Details
- Drehmomentwerte:
- Platte zum Schlitten: 12 bis 15 in·lbs.
- Visier zur Platte: 18 in·lbs.
- Gewicht: 0.75 oz
- Material: 1018 Stahl, schwarz nitridiert