Brownells Österreich - Einer der größten Lieferanten für Waffenteile, Büchsenmacherzubehör & Schießsportzubehör Österreich
696177784845 100041436
An Easy Way to Level Your Optic
The human eye can't detect whether or not a scope reticle is level if the degree is off by 3 degrees or less, but if your scope is off by just 3 degrees, then you're in trouble when it comes to making in-reticle adjustments for those long-range shots. The Fix It Sticks Scope Jack Leveling Tool is designed to get your scope set up right, and it works with any 1/4-inch driver! All you have to do is mount the jack to the Picatinny rail sitting underneath your riflescope. Then turn the drive handle until the arm on the jack engaged with the flat spot underneath your windage and elevation turrets. This ensures that your scope is perfectly level, and the jack will maintain pressure on this flat spot while you tighten your rings down. In order for the Fix It Sticks Scope Jack Leveling Tool to work, you have to have a short section of Picatinny rail sitting just underneath your scope body. Depending on how much clearance is available, you might have to take off the thumb screw and clamp to slide the jack onto the mounting surface from the side. Fix It Sticks says that there must be at least 1/4 inch of clearance to use the jack.
71.9 71.9 1 EUR
Artikel-Nr.: 100041436
FIX IT STICKS SCOPE JACK LEVELING TOOL
Herstellerproduktnummer: FISSJACK 696177784845 Das menschliche Auge kann nicht erkennen, ob ein Zielfernrohrabsehen eben ist oder nicht, wenn der Grad um 3 Grad oder weniger abweicht. Wenn Ihr Zielfernrohr jedoch nur um 3 Grad abweicht, haben Sie Probleme bei der Herstellung von In- Fadenkreuzanpassungen für diese Fernaufnahmen. Das Fix It Sticks Scope Jack Leveling Tool wurde entwickelt, um Ihr Zielfernrohr richtig einzurichten, und funktioniert mit jedem 1/4-Zoll-Treiber! Alles, was Sie tun müssen, ist, den Wagenheber an der Picatinny-Schiene unter Ihrem Zielfernrohr zu befestigen. Drehen Sie dann den Antriebsgriff, bis der Arm am Wagenheber mit der flachen Stelle unter Ihren Wind- und Elevationstürmen in Eingriff steht. Dies stellt sicher, dass Ihr Zielfernrohr perfekt eben ist und der Wagenheber den Druck auf diese flache Stelle aufrechterhält, während Sie Ihre Ringe festziehen. Damit das Fix It Sticks Scope Jack Leveling Tool funktioniert, muss ein kurzer Abschnitt der Picatinny-Schiene direkt unter Ihrem Zielfernrohrkörper sitzen. Je nachdem, wie viel Spiel verfügbar ist, müssen Sie möglicherweise die Rändelschraube und die Klemme abnehmen, um den Wagenheber von der Seite auf die Montagefläche zu schieben. Fix It Sticks sagt, dass mindestens 1/4 Zoll Abstand vorhanden sein muss, um die Buchse zu verwenden.
71.9 EUR 135 71,90 € *
Lieferzeit ca. 14-21 Werktage.
Mehr als 10 Stk. im Lager USA

Eigenschaften

Versandgewicht: 0,045kg Versandhöhe: 25mm Versandbreite: 76mm Versandlänge: 152mm




An Easy Way to Level Your Optic
The human eye can't detect whether or not a scope reticle is level if the degree is off by 3 degrees or less, but if your scope is off by just 3 degrees, then you're in trouble when it comes to making in-reticle adjustments for those long-range shots. The Fix It Sticks Scope Jack Leveling Tool is designed to get your scope set up right, and it works with any 1/4-inch driver! All you have to do is mount the jack to the Picatinny rail sitting underneath your riflescope. Then turn the drive handle until the arm on the jack engaged with the flat spot underneath your windage and elevation turrets. This ensures that your scope is perfectly level, and the jack will maintain pressure on this flat spot while you tighten your rings down. In order for the Fix It Sticks Scope Jack Leveling Tool to work, you have to have a short section of Picatinny rail sitting just underneath your scope body. Depending on how much clearance is available, you might have to take off the thumb screw and clamp to slide the jack onto the mounting surface from the side. Fix It Sticks says that there must be at least 1/4 inch of clearance to use the jack.
Newsletter