Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Die perfekte Lösung für dein Trijicon RMR Rotpunktvisier!
Das S&W M&P TRIJICON RMR SIGHT MOUNT von EGW ist die ideale Halterung für dein Trijicon RMR Rotpunktvisier. Hier sind die Details:
Produktbeschreibung
- Material: 7075 Aluminium
- Beschichtung: Matte Black Hardcoat
- Gesamtlänge: 1.780"
- Gesamtbreite: 1.1"
- Befestigungsmaterial: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw
- Rotpunktkompatibilität: Trijicon RMR
Kompatible Modelle
Diese Halterung passt auf:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Nicht kompatible Modelle
Diese Halterung passt nicht auf:
- Smith & Wesson M&P Shield (Unsere Halterung ist zu breit für die Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Passt nicht auf die M&P .22 Compact. Die hinteren Kimmen von Smith und Wesson können in den Abmessungen variieren. Unsere Halterungen sind nach denselben Toleranzen gefertigt. Einige Benutzer könnten Schwierigkeiten haben, unsere Halterung auf ihrem Schlitten zu installieren, aufgrund der unterschiedlichen Toleranzen. Bitte beachte dies bei der Bestellung.
Installation
Diese Halterungen sollten von einem qualifizierten Büchsenmacher installiert und überprüft werden. Es wird keine Haftung für Schäden oder Verletzungen übernommen, die aus unsachgemäßer Installation oder Verwendung dieses Produkts resultieren.
So installierst du die Halterung:
- Entferne die hintere Kimme*
- Installiere die EGW Sight Mount in die Dovetail
- Ziehe die Set-Schraube fest (falls zutreffend)
- Platziere das Rotpunktvisier auf der EGW Sight Mount (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Halterung erleichtert das Entfernen und hält Loctite vom Rotpunktvisier fern.)
- Trage blauen Loctite auf die mitgelieferten Montageschrauben auf
- Ziehe die Montageschrauben auf 15in/lbs fest
*Ein hinterer Kimme-Pusher ist sehr zu empfehlen.