M-LOK INDEXER The Arisaka Indexer is a continuation of our low profile, minimal control accessories. The Indexer can be used in a variety of ways, but the main intent is to place it between two fingers (usually index and middle). This typically places it further forward on the handguard, which also means it doesn't get in the way when transitioning to kneeling or prone shooting positions, where most people move their support hand towards the rear. Used in this manner, the Indexer makes it much easier to pull the rifle into your shoulder and maintain control while shooting. Additionally, the wider, flatter profile of the Indexer functions very well as a hand stop or barricade stop, and also works as a forward limit to prevent your fingers from slipping off shorter handguards onto a hot barrel or suppressor. KeyMod The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a KeyMod version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires a T15 Torx wrench for installation (not included). Hardware: Two BCM inverted KeyMod screws. Geissele SMR 416 The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a Geissele SMR 416 version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 2.2" Weight: 0.9 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP25 TorxPlus driver for installation (not included). Hardware: Two 10-32x3/8" Torx flat head screws. M-LOK The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for an M-Lok version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP20/T20 Torx wrench for installation (not included). Hardware: Two M-Lok nuts and two 10-24x5/16" Torx button head screws. Made in the USA.
Entdecke den M-LOK INDEXER von ARISAKA DEFENSE!
Der Arisaka Indexer ist die perfekte Ergänzung für deine Waffe, wenn du Wert auf eine niedrige Profilhöhe und minimalen Kontrollaufwand legst.
Produktbeschreibung
Der Indexer kann auf verschiedene Arten verwendet werden, jedoch ist die Hauptintention, ihn zwischen zwei Fingern (in der Regel Zeige- und Mittelfinger) zu platzieren. Dies positioniert ihn weiter vorne am Handguard, was bedeutet, dass er nicht im Weg ist, wenn du zu knienden oder liegenden Schießpositionen wechselst. Die meisten Menschen bewegen ihre Unterstützungshand nach hinten, und mit dieser Verwendung macht es der Indexer viel einfacher, das Gewehr in die Schulter zu ziehen und die Kontrolle während des Schießens zu behalten.
Zusätzlich funktioniert das breitere, flachere Profil des Indexers hervorragend als Handstop oder Barrikadenstop und dient auch als vorderer Begrenzungsstop, um zu verhindern, dass deine Finger von kürzeren Handguards auf einen heißen Lauf oder Suppressor rutschen.
Technische Details
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 1,5"
- Gewicht: 0,6 oz
Der Indexer wird CNC-gefräst aus 6061-T651 Aluminium und ist MIL-A-8625 Typ III hart eloxiert. Für die Installation wird ein T15 Torx-Schlüssel benötigt (nicht im Lieferumfang enthalten).
- Hardware: Zwei BCM umgekehrte KeyMod-Schrauben.
Geissele SMR 416
Der Patent Pending Arisaka Indexer wurde auch für die Geissele SMR 416 entwickelt und bietet ähnliche Vorteile wie die oben genannten Spezifikationen.
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 2,2"
- Gewicht: 0,9 oz
Er wird ebenfalls CNC-gefräst aus 6061-T651 Aluminium und ist MIL-A-8625 Typ III hart eloxiert. Für die Installation wird ein IP25 TorxPlus-Treiber benötigt (nicht im Lieferumfang enthalten).
- Hardware: Zwei 10-32x3/8" Torx-Senkschrauben.
M-LOK
Der M-LOK Indexer ist eine weitere Variante, die speziell für M-LOK Handguards entwickelt wurde, um die Benutzerfreundlichkeit zu maximieren.
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 1,5"
- Gewicht: 0,6 oz
Auch dieser Indexer wird CNC-gefräst aus 6061-T651 Aluminium und ist MIL-A-8625 Typ III hart eloxiert. Für die Installation wird ein IP20/T20 Torx-Schlüssel benötigt (nicht im Lieferumfang enthalten).
- Hardware: Zwei M-LOK-Muttern und zwei 10-24x5/16" Torx-Kopfschrauben.
Hergestellt in den USA.