M-LOK INDEXER The Arisaka Indexer is a continuation of our low profile, minimal control accessories. The Indexer can be used in a variety of ways, but the main intent is to place it between two fingers (usually index and middle). This typically places it further forward on the handguard, which also means it doesn't get in the way when transitioning to kneeling or prone shooting positions, where most people move their support hand towards the rear. Used in this manner, the Indexer makes it much easier to pull the rifle into your shoulder and maintain control while shooting. Additionally, the wider, flatter profile of the Indexer functions very well as a hand stop or barricade stop, and also works as a forward limit to prevent your fingers from slipping off shorter handguards onto a hot barrel or suppressor. KeyMod The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a KeyMod version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires a T15 Torx wrench for installation (not included). Hardware: Two BCM inverted KeyMod screws. Geissele SMR 416 The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a Geissele SMR 416 version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 2.2" Weight: 0.9 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP25 TorxPlus driver for installation (not included). Hardware: Two 10-32x3/8" Torx flat head screws. M-LOK The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for an M-Lok version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP20/T20 Torx wrench for installation (not included). Hardware: Two M-Lok nuts and two 10-24x5/16" Torx button head screws. Made in the USA.
Entdecke den M-LOK INDEXER von ARISAKA DEFENSE!
Der Arisaka Indexer ist eine Weiterentwicklung unserer flachen, minimalen Zubehörteile. Er kann auf vielfältige Weise eingesetzt werden, wobei die Hauptabsicht darin besteht, ihn zwischen zwei Fingern (in der Regel Zeige- und Mittelfinger) zu platzieren. Dies positioniert ihn typischerweise weiter vorne am Handguard, was bedeutet, dass er beim Wechsel in die kniende oder liegende Schießposition nicht im Weg ist, wo die meisten Menschen ihre Unterstützungs-Hand nach hinten bewegen.
In dieser Weise macht der Indexer es viel einfacher, das Gewehr an die Schulter zu ziehen und die Kontrolle beim Schießen zu behalten. Darüber hinaus funktioniert das breitere, flachere Profil des Indexers sehr gut als Handstop oder Barrikadenstop und dient auch als vordere Begrenzung, um zu verhindern, dass deine Finger von kürzeren Handguards auf einen heißen Lauf oder Suppressor rutschen.
KeyMod
Der patentierte Arisaka Indexer ist eine Fortsetzung unserer flachen, minimalen Zubehörteile. Er wurde aufgrund der Nachfrage von Endbenutzern nach einer KeyMod-Version unseres Finger Stops für Picatinny-Schienen entwickelt und bietet ein schlankes Front-zu-Rück-Profil sowie eine leichte Rundung auf beiden Seiten.
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 1,5"
- Gewicht: 0,6 oz
Der Indexer ist CNC-gefräst aus 6061-T651 Aluminium und mit MIL-A-8625 Typ III hart eloxiert. Er benötigt einen T15 Torx-Schlüssel zur Installation (nicht enthalten).
Hardware: Zwei BCM umgekehrte KeyMod-Schrauben.
Geissele SMR 416
Der patentierte Arisaka Indexer ist eine Fortsetzung unserer flachen, minimalen Zubehörteile. Er wurde aufgrund der Nachfrage von Endbenutzern nach einer Geissele SMR 416-Version unseres Finger Stops für Picatinny-Schienen entwickelt und bietet ein schlankes Front-zu-Rück-Profil sowie eine leichte Rundung auf beiden Seiten.
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 2,2"
- Gewicht: 0,9 oz
Der Indexer ist CNC-gefräst aus 6061-T651 Aluminium und mit MIL-A-8625 Typ III hart eloxiert. Er benötigt einen IP25 TorxPlus-Schraubendreher zur Installation (nicht enthalten).
Hardware: Zwei 10-32x3/8" Torx-Senkschrauben.
M-LOK
Der patentierte Arisaka Indexer ist eine Fortsetzung unserer flachen, minimalen Zubehörteile. Er wurde aufgrund der Nachfrage von Endbenutzern nach einer M-LOK-Version unseres Finger Stops für Picatinny-Schienen entwickelt und bietet ein schlankes Front-zu-Rück-Profil sowie eine leichte Rundung auf beiden Seiten.
- Höhe: 1,0"
- Breite: 0,58"
- Länge: 1,5"
- Gewicht: 0,6 oz
Der Indexer ist CNC-gefräst aus 6061-T651 Aluminium und mit MIL-A-8625 Typ III hart eloxiert. Er benötigt einen IP20/T20 Torx-Schlüssel zur Installation (nicht enthalten).
Hardware: Zwei M-LOK-Muttern und zwei 10-24x5/16" Torx-Senkkopfschrauben.
Hergestellt in den USA.